Linear CCM 1 User Manual

PRODUCT DESCRIPTION  
1. REMOVE THE COVER PLATE  
Linear’s Model CCM-1 (P/N ACP00904) CCTV camera can be installed inside the  
AE-100, AE-500, AE-1000 or AE-2000 access control systems. The camera provides  
a video signal for viewing the area in front of the system.  
CCM-1  
REMOVE BOTH  
COVER PLATE  
RETAINING NUTS  
The camera is continuously powered by the access system. Focus has been factory  
adjusted to a range of three to four feet.  
Color  
Camera  
Module  
The AE-1000 and AE-2000 provide a video jack for connection to a video cable with a  
Type “BNC” connector. Up to 400 feet of 75-ohm RG-59 video cable can be used. Longer  
cable runs may require the use of a video amplifier.  
REMOVE THE  
COVER PLATE  
NOTE: If camera is being installed on an existing installation, system power should  
be off prior to installing the camera.  
Installation Instructions  
(760) 438-7000 • FAX (760) 438-7043  
USA & Canada (800) 421-1587 & (800) 392-0123  
Toll Free FAX (800) 468-1340  
2. INSTALL THE WINDOW  
3. REMOVE THE LENS CAP  
4. INSTALL THE CAMERA  
AE-500, AE-1000 AND AE-2000 ONLY  
REMOVE THE LENS CAP  
FROM THE CAMERA LENS  
HOLE IN THE CAMERA  
FRAME IDENTIFIES THE  
TOP OF THE CAMERA  
POSITION THE  
GASKET ON  
THE TWO STUDS  
ATTACH THE CAMERA  
USING THE TWO NUTS  
AE-100 ONLY - IF THE ORIGINAL PROTECTIVE WINDOW IS  
DAMAGED, IT MAY BE REPLACED BY PRESSING IT OUT  
FROM THE OUTSIDE IN. REMOVE THE ADHESIVE BACKING  
FROM THE NEW WINDOW (INCLUDED) AND PRESS IT INTO  
PLACE, ADHESIVE TOWARDS THE FRONT.  
GASKET  
5. CONNECT THE CAMERA AND VIDEO CABLE  
6. TEST CAMERA  
LINEAR LIMITED WARRANTY  
This Linear product is warranted against defects in material and workmanship  
for twenty four (24) months. The Warranty Expiration Date is labeled on the  
product.This warranty extends only to wholesale customers who buy direct from  
Linear or through Linear’s normal distribution channels. Linear does not warrant  
this product to consumers. Consumers should inquire from their selling dealer  
as to the nature of the dealer’s warranty, if any. There are no obligations or  
liabilities on the part of Linear Corporation for consequential damages  
arising out of or in connection with use or performance of this product or  
other indirect damages with respect to loss of property, revenue, or profit,  
or cost of removal, installation, or reinstallation. All implied warranties,  
including implied warranties for merchantability and implied warranties for  
fitness, are valid only until Warranty Expiration Date as labeled on the product.  
This Linear Corporation Warranty is in lieu of all other warranties express  
or implied.  
CAUTION! BE SURE THE SYSTEM POWER IS OFF  
APPLY POWER TO THE ACCESS SYSTEM  
THEN VIEW THE VIDEO MONITOR TO TEST  
THE VIDEO OUTPUT FROM THE CAMERA  
2 CONNECT VIDEO  
CABLE TO VIDEO  
OUTPUT CONNECTOR  
All products returned for warranty service require a Return Product Authorization  
Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an  
RPA# and other important details.  
PLUG THE CAMERA'S  
WIRING HARNESS INTO  
ACCESS SYSTEM'S  
CAMERA CONNECTOR  
USE CABLE TIES TO  
DRESS CABLE  
1
SMALL ADJUSTMENTS FOR TILT  
CAN BE MADE BY ADJUSTING  
THE CAMERA'S BRACKET  
Copyright © 2006 Linear LLC  
221383 C  

RCA EZ3000PL User Manual
Pelco Car Satellite Radio System C579M User Manual
Panasonic P2HD AJ YAX800G User Manual
Panasonic HDC HS20PC User Manual
Panasonic DMCS3K User Manual
Orion Car Audio HCCA COMPETITION HCCA154 User Manual
Magic Chef EWBL20SG User Manual
Legacy Car Audio LCD95MP3 User Manual
Kodak DSKHPSDHC052907 User Manual
Kenwood Car Entertainment System User Manual