Linear TV Receiver DXSR 1504 EC User Manual

PRODUCT DESCRIPTION  
The DXSR-1504/EC and DXSR-1508/EC are four and eight channel supervised digital receivers with solid state outputs  
designed for use with Linear’s DX and DXS Format /EC transmitters. These receivers can be used in a variety of security  
and remote control applications. When the receiver detects a signal from a transmitter programmed into its memory, the  
appropriate channel output activates. The channel outputs have three optional configurations; 3/4 second momentary,  
toggle on/off, and latch until restored. Status and low battery outputs are for supervisory indications. Cutting jumpers select  
which channels require supervisory status reports from transmitters.  
DXSR-1504/EC  
DXSR-1508/EC  
Each unit incorporates a high-sensitivity superheterodyne diversity receiver with two whip antennas. This type of receiver  
provides superior performance by preventing loss of signal due to multi-path interference.  
SUPERVISED  
In a typical installation, the receiver is connected to an alarm control panel, door strike, camera, high current relay or some  
other devices. Transmitters are used to activate or control the devices. The receiver should be mounted indoors or inside  
a weather resistant non-metallic housing for outdoor use.  
DIGITAL RECEIVERS  
The digital DX/DXS code format features over a million possible codes. The transmitters are precoded at the factory to  
unique codes, so no field coding is required. For versatility, any transmitter can be programmed into any receiver channel.  
Receivers must be programmed to recognize the transmitter’s code before system testing and operation. Up to 32  
transmitters can be programmed into the receiver. Each button on multi-button portable transmitters send a unique code,  
and are programmed as separate transmitters.  
Installation Instructions  
The CHANNEL display shows the channels activated and the presence of radio activity. Individual indicators for ALARM,  
STATUS, and LOW BATT show the supervisory status of each receiver channel. All outputs can be configured for normally  
open or normally closed.  
The units can be powered from a 10.2-14.4 VDC or 12-16 VAC power source. The units will draw about 35 mA standby  
and up to 120 mA in alarm.  
(760) 438-7000 • FAX (760) 438-7043  
FEATURES  
COMPONENT LOCATIONS  
STATUS  
ALARM, STATUS,  
& LOW BATTERY  
INDICATORS  
CHANNEL  
DISPLAY  
INDICATOR  
CHANNEL  
DISPLAY  
LOW BATTERY  
INDICATOR  
ALARM  
INDICATOR  
RIGHT ANTENNA  
TERMINAL  
LEFT ANTENNA  
TERMINAL  
AUDIO TEST  
POINT  
OPEN CASE TO  
VIEW COMPONENTS  
RADIO ACTIVITY  
INDICATOR  
GROUND  
TEST POINT  
OUTPUT POLARITY  
JUMPER  
PROGRAM  
JUMPER  
CHANNEL  
BUTTONS  
OUTPUT  
JUMPERS  
CHANNEL BUTTON  
ACCESS PANEL  
TERMINAL  
BLOCK  
CASE LOCKING  
SCREW  
RECESSED WIRING  
ACCESS HOLE  
WIRING STRAIN  
RELIEF POSTS  
STATUS  
JUMPERS  
OPTION JUMPERS AND CHANNEL BUTTONS DETAIL  
MOUNT RECEIVER  
CHANNEL 3  
MOUNT RECEIVER AS HIGH  
CHANNEL 1  
AS PRACTICAL USING  
THE SCREWS AND SCREW  
ANCHORS PROVIDED  
CHANNEL 4  
CHANNEL 2  
STATUS  
JUMPER  
OUTPUT  
JUMPER  
CHANNEL 8  
CHANNEL  
BUTTON  
CHANNEL 7  
CHANNEL 6  
DXSR-1508 ONLY  
CHANNEL 5  
CHANNEL BUTTONS ARE USED DURING PROGRAMMING AND  
TO UNLATCH THE CHANNEL'S OUTPUT IN LATCHED MODE  
OUTPUT JUMPERS SELECT MOMENTARY, TOGGLE, OR  
LATCHED OUTPUT FOR EACH CHANNEL  
WHEN A CHANNEL'S STATUS JUMPER IS CUT, THE CHANNEL  
WILL REQUIRE STATUS TRANSMISSIONS FROM A SUPERVISED  
TRANSMITTER PROGRAMMED INTO THAT CHANNEL  
COVER THE SCREWS WITH THE  
FOUR SCREW HOLE PLUGS PROVIDED  
ATTACH ANTENNAS  
CONNECT TERMINALS  
MODEL DXSR-1508 ONLY  
INSTALL THE TWO  
ANTENNAS UNDER THE  
LEFT AND RIGHT  
ANTENNA TERMINALS  
SECURE WIRES WITH ZIP-TIE  
OUTPUTS TO DEVICE TO BE TRIGGERED  
100 mA MAXIMUM PER OUTPUT  
FROM POWER SOURCE  
10.2-14.4 VDC OR 12-16 VAC  
120 mA MINIMUM  
TIGHTEN ANTENNA TERMINALS WITH  
ANTENNA WHIPS ABOVE THE SCREW  
AND UNDER THE TERMINAL PLATE  
AS SHOWN (BE SURE CASE COVER  
SLOTS ALIGN WITH ANTENNAS)  
WITH OUTPUT POLARITY JUMPER IN  
PLACE, ALL OUTPUTS WILL SWITCH  
TO COMMON WHEN ACTIVE  
NOTE: SEE WIRING EXAMPLES ON  
REVERSE SIDE OF THESE INSTRUCTIONS  
 

La Crosse Technology Portable Radio WS 550 US User Manual
Lenoxx Electronics CD Player CD 895 User Manual
LG Electronics DVD Player LDX 514 User Manual
LG Electronics TV Mount PCM MS2 User Manual
Liebherr Refrigerator 110309 7084282 01 User Manual
Makita Cordless Saw JR14ODWA User Manual
Makita Drill 6227D User Manual
Manitowoc Ice Ice Maker GR 0400A User Manual
Marantz Stereo System SR 19 User Manual
Marshall electronic Car Video System V LCD4 PRO L User Manual