Linear Smoke Alarm DXS 73 User Manual

PRODUCT DESCRIPTION  
REMOVE PROTECTIVE COVER  
The DXS-73 is a photoelectric smoke alarm with a built-in  
transmitter designed for use with Linear’s DXS and DX Format  
receivers. When smoke is detected, the alarm sounds a loud  
local alarm. Twenty seconds after the local alarm sounds, the  
built-in transmitter sends a digitally coded wireless signal to its  
companion receiver. The wireless signal will be repeated every  
20 seconds as long as smoke is still present.  
DXS-73  
SIGNALING  
DXS  
FORMAT  
By  
®
LISTED  
REMOVE  
WIRELESS  
PHOTOELECTRIC  
SMOKE  
PROTECTIVE  
COVER AND  
DISCARD  
The digital DXS code format features over a million possible  
codes. The DXS transmitters are precoded at the factory to  
unique codes, so no field coding is required. The DXS-73 can  
send three different codes: alarm, test and low battery status.  
For versatility, any transmitter can be programmed into any  
receiver channel. Receivers must be programmed to the  
transmitter’s code before system testing and operation.  
Refer to the receiver’s instructions for details on programming.  
The unit is powered by a 3-volt lithium battery. The battery is  
supplied with the transmitter and can power the unit for up to five  
years. Every hour, the DXS-73 will send a status transmission  
to the receiver. The hourly signal updates the receiver to the  
transmitter’s condition. By monitoring status transmissions, the  
receiver can determine if a transmitter has a low battery. If the  
battery voltage drops below a preset level the alarm will sound  
low battery beeps and a low battery signal will be sent to the  
receiver with status reports (some receivers can report low  
battery status, others cannot).  
ALARM  
Installation  
Instructions  
T
C
S
N
I
G
L
S
E
V
MEA 51-07-E  
07257-0895:106  
(760) 438-7000  
USA & Canada (800) 421-1587 & (800) 392-0123  
Toll Free FAX (800) 468-1340  
REMOVE MOUNTING PLATE  
REMOVE BATTERY TAB  
CHOOSE ALARM LOCATION  
TWIST MOUNTING  
PLATE TO UNLOCK  
REMOVE  
BATTERY TAB  
TO APPLY  
POWER  
REMOVE  
MOUNTING  
PLATE  
3-VOLT LITHIUM BATTERY  
TYPES: DURACELL DL123A,  
PANASONIC CR123A,  
SANYO CR123A, ADEMCO 466  
INSTALL MOUNTING PLATE  
PROGRAM RECEIVER  
MOUNT ALARM ON PLATE  
REFER TO RECEIVER'S INSTRUCTIONS TO  
PREPARE RECEIVER TO ACCEPT THE  
TRANSMITTER'S CODE  
SCREW  
ANCHORS  
FOR WALLBOARD  
MATCH ALIGNMENT TABS IN  
PLATE WITH TABS IN COVER  
PRESS AND RELEASE  
TEST BUTTON TO  
SEND SIGNAL  
OR  
A TEST SIGNAL  
WILL BE SENT  
AS SOON AS THE  
SWITCH IS  
TWIST SMOKE  
ALARM CLOCKWISE  
TO LOCK ONTO  
MOUNTING PLATE  
PLASTIC  
SINGLE-GANG  
RELEASED  
ELECTRICAL BOX  
 

KTI Networks Multi tool KGC 311 User Manual
La Crosse Technology Clock 513 149 User Manual
Lathem GPS Receiver ATX GPS User Manual
Lenmar Enterprises Cell Phone Accessories BC3GS User Manual
LG Electronics Clothes Dryer DLE3777W User Manual
Liebert Power Supply NX UPS System User Manual
Life Fitness Bicycle 95CXL User Manual
Magnavox CD Player AZ7275 User Manual
Makita Grinder 9501BKLT User Manual
Memorex Karaoke Machine MKS SS1 User Manual