Linear Satellite Radio DXS 32 EC User Manual

PRODUCT DESCRIPTION  
The DXS-32/EC is a battery powered stationary transmitter designed for use with Linear’s DXS and  
DX format receivers. This transmitter can be used in a variety of wireless remote control applications.  
Triggering the transmitter with its built-in magnetic switch sends a digitally coded wireless signal to  
its companion receiver.  
DXS-32/EC  
BY  
The digital DXS code format features over a million possible codes. The DXS transmitters are  
precoded at the factory to unique codes, so no field coding is required. The DXS-32/EC can send  
four different codes: alarm, restore, low battery and status.  
MINIATURE  
Receivers must be programmed to the transmitter’s code before system testing and operation. Refer  
to the receiver’s instructions for details on programming.  
SUPERVISED  
DOOR/WINDOW  
TRANSMITTER  
In a typical installation, the magnet is mounted on a door or window and the transmitter is mounted  
on the frame. When the magnet moves more than 1 cm away from the transmitter, an alarm signal  
is sent. When the magnet returns next to the unit, a restore signal is sent. The magnet is adjustable  
with four height positions. A 0.5 cm high magnet spacer is also supplied to snap on to the base of  
the magnet.  
The transmitter is powered from two 3-Volt #2032 lithium batteries with an expected battery life of  
up to 4 years. Every hour, the DXS-32/EC will send a status transmission to the receiver. The hourly  
signal updates the receiver to the transmitter’s condition. By monitoring status transmissions, the  
receiver can determine if a transmitter has a low battery or has been removed from the system. DXS  
format receivers can monitor status signals, DX format receivers cannot.  
Installation Instructions  
Normally, the transmitter sends an exit/entry delay transmission code. Cutting an internal jumper  
selects an instant transmission code. Cutting this jumper doesn’t change the time of the actual  
transmissions, but changes the code of the signal sent sothereceivercandeterminethetransmitter’s  
function.  
(760) 438-7000 FAX (760) 438-7043  
DXS-32/EC FEATURES & ACCESSORIES  
OPENING CASE  
MAGNET  
ALIGNMENT  
MARKS  
REMOVE THE CASE TOP BY TWISTING A  
SMALL FLAT BLADE SCREWDRIVER IN  
TRANSMITTER  
THE SLOT ON EITHER END OF THE TRANSMITTER  
MAGNET  
SIDE  
MARK  
MAGNET  
ALIGNMENT  
MARKS  
TRANSMITTER  
SCREWS AND  
DOUBLE STICK TAPE  
MAGNET CAN BE MOUNTED UP TO  
1 cm FROM LEFT SIDE OF  
TWIST  
TRANSMITTER  
ADJUSTABLE  
MAGNET  
MAGNET  
ADJUSTMENT  
TAB (EACH SIDE)  
MAGNET  
SCREWS AND  
DOUBLE STICK TAPE  
SQUEEZE MAGNET TABS TO  
ADJUST MAGNET HEIGHT (4 POSITIONS)  
REMOVE BATTERY PROTECTION STRIP  
COMPONENT LOCATIONS  
ANTENNA  
TWO TYPE 2032  
BATTERIES  
PULL OUT & DISCARD  
BATTERY PROTECTION  
STRIP TO ACTIVATE  
TRANSMITTER  
DELAY/INSTANT JUMPER  
(CUT JUMPER FOR INSTANT)  
 

KWC Indoor Furnishings 27240050000 User Manual
La Crosse Technology Weather Radio WS 9057U User Manual
Learning Resources Games LER 0341 User Manual
LG Electronics Projector CD181D User Manual
Linksys Network Card WPC300N User Manual
Lochinvar Gas Heater LVNL 041 User Manual
LOREX Technology Computer Monitor L19WD800 User Manual
Makita Cordless Drill 6073D and 6073DW User Manual
Makita Cordless Saw 5093D User Manual
Melissa Vacuum Cleaner 640 142 User Manual