Linear Automobile Alarm DXS 72 EC User Manual

PRODUCT DESCRIPTION  
REMOVE MOUNTING PLATE  
The DXS-72/EC is a photoelectric smoke alarm with a built-in  
transmitter designed for use with Linear’s DXS and DX Format  
receivers. When smoke is detected, the alarm sounds a loud local  
alarm. Twenty seconds after the local alarm sounds, the built-in  
transmitter sends a digitally coded wireless signal to its companion  
receiver. The wireless signal will be repeated every 20 seconds as  
long as smoke is still present.  
MATCH UP  
ALIGNMENT  
TABS  
DXS-72/EC  
DXS  
FORMAT  
By  
WIRELESS  
PHOTOELECTRIC  
SMOKE  
The digital DXS code format features over a million possible codes.  
The DXS transmitters are precoded at the factory to unique codes,  
so no field coding is required. The DXS-72/EC can send three  
different codes: alarm, test and low battery status.  
ALARM  
For versatility, any transmitter can be programmed into any receiver  
channel. Receivers must be programmed to the transmitter’s  
code before system testing and operation. Refer to the receiver’s  
instructions for details on programming.  
Installation  
Instructions  
The unit is powered by two 9-volt alkaline or lithium batteries. These  
batteries are supplied with the transmitter and can power the unit  
for up to two years. Every hour, the DXS-72/EC will send a status  
transmission to the receiver. The hourly signal updates the receiver  
to the transmitter’s condition. By monitoring status transmissions, the  
receiver can determine if a transmitter has a low battery or has been  
removed from the system. If the battery voltage drops below a preset  
level the alarm will sound low battery beeps and a low battery signal  
will be sent to the receiver with status reports (some receivers can  
report low battery status, others cannot).  
TWIST SMOKE  
ALARM CLOCKWISE  
TO LOCK TO MOUNTING  
PLATE  
(760) 438-7000 • FAX (760) 438-7043  
NOTE: After replacing batteries, press transmitter test button  
to reset “low battery circuit”.  
DXS-72/EC FEATURES  
INSTALL BATTERIES  
CHOOSE ALARM LOCATION  
PRESS TRANSMITTER TEST BUTTON  
AFTER INSTALLING BATTERIES  
TO RESET LOW BATTERY CIRCUIT  
READ THE STANDARD FOR SMOKE ALARM  
LOCATION ON THE BACK OF THESE INSTRUCTIONS  
TRANSMIT LED  
TRANSMITTER  
TEST BUTTON  
TRANSMITTER  
BOARD  
DETERMINE THE PROPER LOCATION FOR THE ALARM  
BED  
ROOM  
BED  
ROOM  
HALL  
LIVING  
ROOM  
RECREATION ROOM  
CONNECT AND  
INSTALL TWO  
9-VOLT BATTERIES  
BASEMENT  
Indicates required smoke alarm  
Indicates optional smoke alarm  
if door is not provided between  
Living and Recreation Rooms  
9-VOLT BATTERY TYPES:  
EVEREADY 216, 522, OR 1222  
DURACELL MN1604  
BATTERY  
HOLDING  
CUPS  
GOLD PEAK 1604P, 1604S  
ULTRALIFE LITHIUM U9VL  
INSTALL MOUNTING PLATE  
PROGRAM RECEIVER  
MOUNT ALARM ON PLATE  
MATCH UP  
ALIGNMENT  
TABS  
REFER TO RECEIVER'S INSTRUCTIONS  
TO PREPARE RECEIVER TO ACCEPT THE  
TRANSMITTER'S CODE  
SCREW  
ANCHORS  
FOR WALLBOARD  
PRESS TRANSMITTER  
TEST BUTTON  
TO SEND SIGNAL  
OR  
PLASTIC  
SINGLE-GANG  
ELECTRICAL  
BOX  
TWIST SMOKE  
ALARM CLOCKWISE  
TO LOCK TO MOUNTING  
PLATE  
 

La Crosse Technology Portable Radio WS 9730U IT User Manual
Learning Resources Games LER 5051 User Manual
LG Electronics Washer WM2016C User Manual
Life Fitness Elliptical Trainer 14 90 Series User Manual
Lyngdorf Audio Stereo Amplifier DPA 1 User Manual
Magellan Telephone GLOBAL SATELLITE TELEPHONE User Manual
Magnavox Pet Fence FW58 User Manual
Makita Cordless Drill 5007S User Manual
Memorex MP3 Player MP3122 User Manual
Memorex Stereo System MX5310 User Manual