LG Electronics Speaker System LAP340 User Manual

OWNER’S MANUAL  
SoundPlate™  
LAP340 / LAP341  
Please read this manual carefully before operating your set and retain it  
for future reference.  
 
LAP340-NB_DARELLK_ENG.indd  
1
2013-10-30  
9:11:49  
Getting Started  
3
WARNING: Do not install this equipment in a  
confined space such as a book case or similar unit.  
Safety Information  
CAUTION: Do not block any ventilation openings.  
Install in accordance with the manufacturer’s  
instructions.  
CAUTION  
1
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
Slots and openings in the cabinet are provided for  
ventilation and to ensure reliable operation of the  
product and to protect it from over heating. The  
openings shall be never be blocked by placing  
the product on a bed, sofa, rug or other similar  
surface. This product shall not be placed in a built-  
in installation such as a bookcase or rack unless  
proper ventilation is provided or the manufacturer’s  
instruction has been adhered to.  
CAUTION: TO REDUCE THE RISK OF ELECTRIC  
SHOCK DO NOT REMOVE COVER (OR BACK) NO  
USER-SERVICEABLE PARTS INSIDE REFER SERVICING  
TO QUALIFIED SERVICE PERSONNEL.  
This lightning flash with arrowhead  
symbol within an equilateral  
triangle is intended to alert the  
user to the presence of uninsulated  
dangerous voltage within the  
product’s enclosure that may be of  
sufficient magnitude to constitute a  
risk of electric shock to persons.  
CAUTION concerning the Power Cord  
Most appliances recommend they be placed upon  
a dedicated circuit;  
That is, a single outlet circuit which powers only  
that appliance and has no additional outlets or  
branch circuits. Check the specification page of this  
owner’s manual to be certain. Do not overload wall  
outlets. Overloaded wall outlets, loose or damaged  
wall outlets, extension cords, frayed power cords, or  
damaged or cracked wire insulation are dangerous.  
Any of these conditions could result in electric  
shock or fire. Periodically examine the cord of your  
appliance, and if its appearance indicates damage  
or deterioration, unplug it, discontinue use of the  
appliance, and have the cord replaced with an  
exact replacement part by an authorized service  
centre. Protect the power cord from physical or  
mechanical abuse, such as being twisted, kinked,  
pinched, closed in a door, or walked upon. Pay  
particular attention to plugs, wall outlets, and  
the point where the cord exits the appliance. To  
disconnect power from the mains, pull out the  
mains cord plug. When installing the product,  
ensure that the plug is easily accessible.  
The exclamation point within an  
equilateral triangle is intended  
to alert the user to the presence  
of important operating and  
maintenance (servicing) instructions  
in the literature accompanying the  
product.  
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK  
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN  
OR MOISTURE.  
CAUTION: The apparatus shall not be exposed to  
water (dripping or splashing) and no objects filled  
with liquids, such as vases, shall be placed on the  
apparatus.  
NOTICE: For Product Identification and  
Compliance/Safety labeling information please  
refer to Main label on the bottom of unit.  
 
LAP340-NB_DARELLK_ENG.indd  
3
2013-10-30  
9:11:49  
4
Getting Started  
This device is equipped with a portable battery or  
accumulator.  
Safety way to remove the battery or the  
battery from the equipment: Remove the  
old battery or battery pack, follow the steps  
in reverse order than the assembly. To prevent  
contamination of the environment and bring on  
possible threat to human and animal health, the  
old battery or the battery put it in the appropriate  
container at designated collection points. Do  
not dispose of batteries or battery together with  
other waste. It is recommended that you use  
local, free reimbursement systems batteries and  
accumulators. The battery shall not be exposed to  
excessive heat such as sunshine, fire or the like.  
1
 
LAP340-NB_DARELLK_ENG.indd  
4
2013-10-30  
9:11:49  
Table of Contents  
5
Table of Contents  
1
1
Getting Started  
3
6
6
6
7
Safety Information  
Unique features  
Introduction  
Accessories  
Front panel  
2
3
4
7
8
Rear panel  
Remote control  
10 Setting up the unit  
2
Operating  
13  
Basic operations  
13 – Optical input operation  
13 – LG Sound Sync  
14 – AUTO POWER On/Off  
15  
Using Bluetooth technology  
15 – Listening to music stored on the  
Bluetooth devices  
16  
CINEMA SOUND  
3
Troubleshooting  
17  
Troubleshooting  
4
Appendix  
18 Specifications  
19  
19  
Trademarks and licenses  
Maintenance  
19 – Handling the unit  
 
LAP340-NB_DARELLK_ENG.indd  
5
2013-10-30  
9:11:49  
6
Getting Started  
Unique features  
Accessories  
Please check and identify the supplied accessories.  
LG Sound Sync  
Controls volume level of this unit by the remote  
control of your LG TV that is compatible with LG  
Sound Sync.  
1
Designs and specifications of the accessories are  
subject to change without prior notice.  
Bluetooth  
Enjoys music from bluetooth device with simple  
connection.  
Remote Control (1)  
Power cord (1)  
Battery (1)  
Introduction  
Symbols used in this manual  
Optical cable (1)  
Note  
,
Indicates special notes and operating features.  
Caution  
>
Indicates cautions for preventing possible damages  
from abuse.  
Cable holder (1)  
Screw (2)  
Cable ties for arranging  
cables (2)  
 
LAP340-NB_DARELLK_ENG.indd  
6
2013-10-30  
9:11:51  
Getting Started  
7
Front panel  
1
ARemote sensor  
BLED indicator  
You can check the current state of the unit by the colour LED on it. Refer to the table below.  
LED Colour  
Red  
Orange  
Green  
White  
LED State  
Off  
Power on or disconnected power cord  
On  
Standby  
-
-
-
-
-
Blink  
(Twice rapidly)  
CINEMA SOUND  
is off.  
CINEMA SOUND  
is on.  
Blink  
LG sound sync  
(LG TV) ready  
Booting  
Mute  
-
Bluetooth ready  
-
-
(Twice per second)  
Blink  
(Once per second)  
-
-
On -> Off  
(After 3 seconds)  
Optical function  
selected  
LG sound sync  
(LG TV) paired  
Bluetooth paired  
Rear panel  
A
BC  
D
A1/!(Standby/On)  
CAUTO POWER ON/OFF  
Turns on or off AUTO POWER function.  
o/p (Volume)  
Adjusts speaker volume.  
DAC power input  
F (Function)  
Press it repeatedly to select other function.  
BOptical input  
 
LAP340-NB_DARELLK_ENG.indd  
7
2013-10-30  
9:11:51  
8
Getting Started  
Remote control  
1
Turns on or off CINEMA SOUND  
function.  
Switches the unit ON or OFF.  
Reduce the sound volume.  
Mutes or unmutes the sound.  
Select LG TV function.  
Increase the sound volume.  
Select Optical function.  
Select Bluetooth function.  
Note  
,
Once the unit is shut down to standby,  
please wait several seconds before trying to  
use remote again.  
y
y
y
When you press any button on the remote  
control, the red LED on the main unit blinks  
twice. (Except 1(Power), CINEMA SOUND)  
The colour LED that indicates the current  
function is lit up for about 3 seconds  
when you press the function buttons : h,  
OPTICAL, LG TV.  
The red LED on Unit will be lit If the volume  
level is adjusted between minimum to  
maximum.  
y
The red LED blinks twice rapidly when  
CINEMA SOUND function is off.  
y
y
The green LED blinks twice rapidly when  
CINEMA SOUND function is on.  
 
LAP340-NB_DARELLK_ENG.indd  
8
2013-10-30  
9:11:52  
Getting Started  
9
3. Put the battery cover on the remote control and  
turn it clockwise to close.  
Battery installation  
Caution  
>
Do not open the battery cover by using your  
finger. Or else, your nail could break.  
1
1. Turn the battery cover counterclockwise by  
using a coin. Then take the battery cover.  
Warning  
!
DO NOT INGEST BATTERY. CHEMICAL BURN  
HAZARD.  
2. Insert and fix the battery with the minus (-)  
facing in the same direction as the minus (-) on  
the battery compartment.  
Caution  
>
The battery used in this device may present  
a fire or chemical burn hazard if mistreated.  
Do not recharge, disassemble, incinerate,  
or heat above 100 °C (212 °F). Replace  
the battery part no. CR2025 only. Use of  
another battery may present a risk of fire  
or explosion. Dispose of used battery.  
Keep battery away from children. Do not  
disassemble or dispose of in fire.  
y
+
[The remote control supplied with] This  
product contains a coin/button cell battery.  
If the coin/button cell battery is swallowed,  
it can cause severe internal burns in just  
2 hours and can lead to death. Keep new  
and used batteries away from children. If  
the battery compartment does not close  
securely, stop using the product and keep  
it away from children. If you think batteries  
might have been swallowed or placed  
inside any part of the body, seek immediate  
medical attention.  
y
 
LAP340-NB_DARELLK_ENG.indd  
9
2013-10-30  
9:11:53  
10 Getting Started  
Caution  
>
Setting up the unit  
This unit is designed to be positioned under your  
TV.  
Do not try to set up this unit alone. It may  
need at least 2 persons to lift your TV.  
Otherwise it may result in a personal injury  
and/or property damages.  
y
y
1
Before setting up this system with your TV, make  
sure your TV's specifications.  
Do not connect a CRT type TV to this unit.  
Because this unit contains magnetic parts,  
colour irregularity may occur on the TV  
screen.  
Weight  
y
Do not put the other objects except a TV or  
a monitor on the unit.  
y
y
y
The unit must be set up on a stable and  
horizontal surface.  
Do not put any other object between the  
unit and the supporting furniture when you  
set up the unit.  
Recommendation  
It is recommended to set up the unit on a  
sufficiently firm and horizontal surface.  
,
Max. 38 kg  
1. Place the unit on the position where you want  
to place your TV.  
Size of the base  
y
Max. 270 mm  
Max. 680 mm  
 
LAP340-NB_DARELLK_ENG.indd 10  
2013-10-30  
9:11:53  
Getting Started 11  
Note  
2. Connect the optical cable and the power cord  
to the unit.  
,
You can arrange the cables of the unit.  
1. Fix the cable holder with screws.  
1
2. Arrange the cables as the below.  
3. Connect another end of optical cable  
connecting the unit to your TV.  
4. Place your TV on the centre of the unit.  
5. Plug in the power cord of the unit.  
 
LAP340-NB_DARELLK_ENG.indd 11  
2013-10-30  
9:11:54  
12 Getting Started  
Caution  
Do not place your TV on the edge of this  
unit. Otherwise it may result in a personal  
injury and/or property damages.  
>
How to Affix the Ferrite Core  
(Optional)  
You may need to attach Ferrite core in order to  
reduce or eliminate any electrical interference.  
y
1
If your TV is over recommended weight  
(max 38 kg) or has a Base larger in area than  
the Unit do NOT place TV on the Unit.  
y
-
In this case, it is recommended to place this  
system in another location such as on the  
shelf under the TV.  
1. Pull the stopper [a] of the ferrite core to open.  
2. Wind the power cord around the ferrite core  
once.  
3. Close the ferrite core until it clicks.  
 
LAP340-NB_DARELLK_ENG.indd 12  
2013-10-30  
9:11:55  
Operating 13  
LG Sound Sync  
Basic operations  
Optical input operation  
You can control some functions of this unit by  
your TV's remote control with LG Sound Sync. It  
is compatible with the LG TV that is supported LG  
Sound Sync. Make sure of the LG Sound Sync logo  
on your TV.  
Note  
,
Before operating this Unit it is advised to turn  
OFF TV speaker Sound as it may create sound  
differences between the 2 products running  
simultaneously.  
2
Controllable function by LG TV's remote control :  
Volume up/down, mute  
Refer to TV menu/Specifications and select  
from below methods :  
Refer to the TV's instruction manual for the details  
of LG Sound Sync.  
-
-
Mute your TV.  
Select [O] on the TV sound setup menu  
not to output the sound through the TV.  
Make one of the following connections, depending  
on the capabilities of your equipment.  
-
Select [Optical output] on the TV sound  
setup menu to listen to the sound through  
this unit.  
Note  
,
You can also use the remote control of  
this unit while using LG Sound Sync. If you  
use TV's remote control again, the unit  
synchronizes with the TV.  
y
1. Connect your TV to the unit by using an optical  
cable. (Refer to the pages 10 - 11.)  
When the connections failed, make sure of  
the condition of the TV and power of it.  
y
y
2. Turn on the unit by pressing 1(Power) on the  
remote control.  
Make sure of the condition of this unit and  
the connection in the cases below when  
using LG Sound Sync.  
3. Select OPTICAL function by using OPTICAL on  
the remote control.  
Green LED on the unit is lit up for about 3  
seconds and you can listen to the TV's sound.  
- Turned off the unit.  
- Changing the function to the others.  
- Disconnecting the optical cable.  
- Disconnecting the wireless connection  
caused by interference or a distance.  
The amount of time to turn off this unit is  
different depending on your TV when you  
set AUTO POWER function to ON.  
y
 
LAP340-NB_DARELLK_ENG.indd 13  
2013-10-30  
9:11:55  
14 Operating  
With wired connection  
1. Connect your LG TV to the unit by using an  
optical cable. (Refer to the pages 10 - 11.)  
AUTO POWER On/Off  
This function automatically turns on/off the unit  
when you turn on/off the TV or the external device  
(DVD Player, Blu-ray Disc Player, etc.) connected to  
this unit.  
2. Set up LG Sound Sync (Optical) on the TV. Refer  
to the TV's instruction manual.  
It is supported only on OPTICAL and LG TV  
functions.  
3. Turn on the unit by pressing 1(Power) on the  
remote control.  
You can turn on or off AUTO POWER function by  
using AUTO POWER ON/OFF switch on the rear  
panel of the unit.  
4. Select OPTICAL function by using OPTICAL on  
the remote control.  
2
Green LED on the unit is lit up for about 3  
seconds and you can listen to the TV's sound.  
Note  
,
After the unit is turned on by AUTO POWER  
function, it will be automatically turned off if  
there is no signal for a certain period of time  
from the TV connected by LG Sound Sync  
(Optical/Wireless).  
y
With wireless connection  
1. Turn on the unit by pressing 1(Power) on the  
remote control.  
2. Select LG TV function by using LG TV on the  
remote control. Then white LED on the unit  
starts to blink.  
After the unit is turned on by AUTO POWER  
function, it will be automatically turned off if  
there is no signal for a certain period of time  
from the external device connected by an  
optical cable.  
y
3. Set up LG Sound Sync (Wireless) on the TV. Refer  
to the TV's instruction manual.  
When connection is completed normally  
between this unit and your TV, white LED on  
the unit is lit up for about 3 seconds.  
AUTO POWER function is initially turned on.  
y
y
If you turned off the unit directly, it cannot  
be turned on automatically by AUTO POWER  
function. However the unit can be turned  
on by AUTO POWER function when optical  
signal comes in after 5 seconds of no signal.  
Note  
,
If you turned off the unit directly by pressing  
1(Power), LG Sound Sync (Wireless) will be  
disconnected. To use this function again, you  
should reconnect the TV and the unit.  
Depending on the connected device, this  
function may not operate.  
y
y
When booting this unit on LG TV fucntion,  
it takes about 25 seconds to turn it on and  
the red LED is blinking twice per second.  
During that time, you cannot control this  
unit except turn it off.  
In Bluetooth mode, this unit may be turned  
on by AUTO POWER setting depending on  
the connected Bluetooth device and then  
LG TV function is selected.  
y
In this case the unit will be turned off  
automatically and when you restart the unit,  
it will be turned on by LG TV function.  
 
LAP340-NB_DARELLK_ENG.indd 14  
2013-10-30  
9:11:56  
Operating 15  
Auto power down  
Listening to music stored on  
the Bluetooth devices  
This unit will turn itself off to save electric  
consumption in the case were main unit is not  
connected to external device and is not used for  
25 minutes.  
Pairing this unit and Bluetooth  
device  
Before you start the pairing procedure, make  
sure the Bluetooth feature is turned on in to your  
Bluetooth device. Refer to your Bluetooth device’s  
user guide. Once a pairing operation is performed,  
it does not need to be performed again.  
Using Bluetooth  
technology  
2
1. Select the Bluetooth function by using h on  
the remote control. Then the orange LED on the  
unit starts to blink.  
About Bluetooth  
Bluetooth is wireless communication technology  
for short range connection.  
2. Operate the Bluetooth device and perform the  
pairing operation. When searching for this unit  
with the Bluetooth device, a list of the devices  
found may appear in the Bluetooth device  
display depending on the type of Bluetooth  
device. Your unit appears asLG SOUND PLATE  
(XX:XX).  
The sound may be interrupted when there is  
interference by the other electronic waves which  
run on same frequency or if you connect bluetooth  
devices in the other rooms nearby.  
Connecting individual devices under Bluetooth®  
wireless technology does not incur any charges. A  
mobile phone with Bluetooth® wireless technology  
can be operated via the Cascade if the connection  
was made via Bluetooth® wireless technology.  
Note  
,
XX:XX means the last four digits of BT  
address. For example, if your unit has a  
BT address such as 9C:02:98:4A:F7:08,  
you will seeLG SOUND PLATE (F7:08)on  
your Bluetooth device.  
y
Available Devices : Mobile phone, MP3, Laptop,  
PDA etc.  
Depending on the Bluetooth device type,  
some device have a different pairing way.  
Enter the PIN code (0000) as needed.  
y
Bluetooth profiles  
In order to use Bluetooth® wireless technology,  
devices must be able to interpret certain profiles.  
This unit is compatible with following profile.  
3. The orange LED is lit up for about 3 seconds  
when this unit successfully paired with your  
Bluetooth device.  
A2DP (Advanced Audio Distribution Profile)  
4. Listen to music.  
To play a music stored on your Bluetooth device,  
refer to your Bluetooth device’s user guide.  
 
LAP340-NB_DARELLK_ENG.indd 15  
2013-10-30  
9:11:56  
16 Operating  
Note  
,
CINEMA SOUND  
When watching movies, you can enjoy optimized  
sound effect through the prominent bass and  
cinematic surround effect.  
When using Bluetooth® technology, you  
y
have to make a connection between the  
unit and the bluetooth device as close as  
possible and keep the distance.  
However it may not work well in the case  
below :  
Turn on or off the sound effect by using CINEMA  
SOUND on the remote control.  
- There is a obstacle between the unit and  
the bluetooth device.  
Note  
,
- There is a device using same frequency  
with Bluetooth® technology such as a  
medical equipment, a microwave or a  
wireless LAN device.  
2
CINEMA SOUND will be turned off when you  
restart the unit.  
You should connect your Bluetooth device  
to this unit again when you restart it.  
y
y
When you select Bluetooth function again  
after changing to other functions, Bluetooth  
connection may be disconnected. You  
should reconnect the bluetooth device to  
use this function.  
The sound may be interrupted when  
the connection interfered by the other  
electronic wave.  
y
You cannot control the Bluetooth device  
with this unit.  
y
y
y
Pairing is limited one Bluetooth device per  
one unit and multi-pairing is not supported.  
Depending on the type of the device,  
you may not be able to use the Bluetooth  
function.  
You can enjoy wireless system using phone,  
MP3, Notebook, etc..  
y
y
The more distant between the unit and  
the bluetooth device, the lower the sound  
quality becomes.  
Bluetooth connection will be disconnected  
when the unit is turned off or the bluetooth  
device gets far from the unit.  
y
y
y
When Bluetooth connection is  
disconnected, connect the bluetooth device  
to the unit again.  
When not connected the Bluetooth, orange  
LED is blinking.  
 
LAP340-NB_DARELLK_ENG.indd 16  
2013-10-30  
9:11:56  
Troubleshooting 17  
Troubleshooting  
PROBLEM  
CAUSE & CORRECTION  
The power cord is unplugged.  
y
Plug in the power cord.  
No Power  
No sound  
Check the condition by operating other electronic devices.  
y
y
Incorrect input source is selected.  
Check the input source and select the correct input source.  
The mute function is activated.  
y
Press i or adjust the volume level to cancel the mute function.  
The remote control is too far from the unit.  
Operate the remote control within about 7 m.  
y
y
y
3
The remote control  
does not work  
properly.  
There is an obstacle in the path of the remote control and the unit.  
Remove the obstacle.  
The battery in the remote control is exhausted.  
Replace the battery with new one.  
The AUTO POWER  
on/off function does  
not work.  
Depending on the connected device, this function may not operate.  
y
y
Check the status of AUTO POWER ON/OFF switch on the rear panel of the unit.  
Check the details below and adjust the unit according to them.  
With the unit connected with TV, change the AUDIO DIGITAL OUT setting on TV  
Setup Menu from [PCM] to [AUTO] or [BITSTREAM].  
y
y
y
When you feel the  
output sound of the  
unit is low.  
With the unit connected with Player, change the AUDIO DIGITAL OUT setting on  
Player Setup Menu from [PCM] to [PRIMARY PASS-THROUGH] or [BITSTREAM].  
Change Audio DRC setting on Player setup menu to [OFF] state.  
Depending on the type of the furniture where the unit is placed, you might hear a  
slight noise from the furniture due to the dual subwoofers built within the product.  
There is a noise on  
the periphery of the  
unit.  
Check the supporting furniture whether it is sufficiently firm and horizontal.  
y
y
However, if you still hear a noise, place a tablecloth between the unit and the  
surface.  
 
LAP340-NB_DARELLK_ENG.indd 17  
2013-10-30  
9:11:56  
18 Appendix  
Specifications  
General  
Power requirements  
Power consumption  
Dimensions (W x H x D)  
Net Weight (Approx.)  
Operating temperature  
Operating humidity  
Refer to the main label on the unit.  
Refer to the main label on the unit.  
(700 x 38.5 x 320) mm (With foot)  
3.8 kg  
5 °C to 35 °C (41 °F to 95 °F)  
5 % to 90 %  
Inputs  
DIGITAL IN (OPTICAL IN)  
3.3 V (p-p), Optical jack  
Available Digital Input Audio  
Sampling Frequency  
32 kHz, 44.1 kHz, 48 kHz, 96 kHz  
Amplifier  
4
Total output  
Stereo mode  
Surround mode  
Built-In subwoofer  
THD  
120 W  
20 W x 2 (8 Ω at 1 kHz)  
20 W x 2 (8 Ω at 1 kHz)  
40 W (4 Ω at 100 Hz)  
0.1 %  
Designs and specifications are subject to change without prior notice.  
y
 
LAP340-NB_DARELLK_ENG.indd 18  
2013-10-30  
9:11:56  
Appendix 19  
Trademarks and  
licenses  
Maintenance  
Handling the unit  
When shipping the unit  
Manufactured under license from Dolby  
Laboratories. Dolby and the double-D symbol  
are trademarks of Dolby Laboratories.  
Please save the original shipping carton and  
packing materials. If you need to ship the unit, for  
maximum protection, re-pack the unit as it was  
originally packed at the factory.  
Keeping the exterior surfaces clean  
Manufactured under license under U.S. Patent  
Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S.  
and worldwide patents issued & pending. DTS,  
the Symbol, & DTS and the Symbol together are  
registered trademarks & DTS 2.0 Channel is a  
trademark of DTS, Inc. Product includes software.  
© DTS, Inc. All Rights Reserved.  
Do not use volatile liquids such as insecticide  
spray near the unit.  
y
y
y
Wiping with strong pressure may damage the  
surface.  
Do not leave rubber or plastic products in  
contact with the unit for a long period of time.  
4
Cleaning the unit  
To clean the player, use a soft, dry cloth. If the  
surfaces are extremely dirty, use a soft cloth lightly  
moistened with a mild detergent solution. Do not  
use strong solvents such as alcohol, benzine, or  
thinner, as these might damage the surface of the  
unit.  
Bluetooth® wireless technology is a system which  
allows radio contact between electronic devices.  
Connecting individual devices under Bluetooth®  
wireless technology does not incur any charges.  
A mobile phone with Bluetooth® wireless  
technology can be operated via the Cascade if  
the connection was made via Bluetooth® wireless  
technology.  
The Bluetooth® word mark and logos are owned  
by the Bluetooth® SIG, Inc. and any use of such  
marks by LG Electronics is under license.  
Other trademarks and trade names are those of  
their respective owners.  
 
LAP340-NB_DARELLK_ENG.indd 19  
2013-10-30  
9:11:57  
 
LAP340-NB_DARELLK_ENG.indd 20  
2013-10-30  
9:11:57  

LevelOne Switch IPS 0008 User Manual
LG Electronics Cell Phone VX3450L User Manual
Makita Sander BO6040 003278 User Manual
Master Bilt Oven PPT 67 User Manual
Maxon Telecom Network Card MM 5100 User Manual
Maytag Dishwasher W10185071B User Manual
McCulloch Lawn Mower MC175H42ST User Manual
Melissa Styling Iron 635 071 User Manual
Memorex TV VCR Combo MVT2090 User Manual
Metra Electronics Car Stereo System AW 200GM User Manual